Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and technical knowledge. They can create and program keys more quickly and at a lower cost than dealers.
A dead battery for your coin is most likely to be the cause the reason your key-fob stops locking or unlocking doors. There are other causes for the key to be malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking, and won't start the engine. In this scenario you'll need to use the alternative starting method that is described in the owner's manual.
The spark plugs could also be worn out. Spark plugs are what ignite the fuel to start the engine. However they have a finite lifespan. They'll eventually fail if they aren't used frequently enough.
Luckily, there's peugeot 207 replacement key cost G28 for this issue. Check the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts then it's time to replace it. It is also essential to clean the battery's contacts when it has corrosion. This can be accomplished by removing the rubber covers from the two terminals of the battery, and then using a wirebrush to remove any corroded battery parts. Then, you should connect your cables to connect the positive and negative poles.
Water Damage
If your 208 doesn't start and the battery isn't running, then make sure whether the spark plugs are functioning. You might find that they're filthy and don't spark. The spark plugs can be cleaned in a workshop.
Peugeot automobiles use transponder keys that is compatible with the car's immobiliser system. This ensures only the correct key can turn the engine. If the chip in the Peugeot key is damaged, it won't send the proper signal to the vehicle.
This is a typical issue that can be caused by water damage. This is particularly prevalent in colder climates, where the vehicle could have been exposed to snow or rain. In this situation, contact a trusted locksmith who will have the tools and equipment needed to modify the key. They also have the latest technological know-how and the equipment required to make the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot changed from the old carbon encased transponder chips and introduced a new kind of chip that utilizes electronic components on circuit boards. The new system is effective when it's brand new but over time the circuit boards start to deteriorate and stop working properly.
This can stop the immobiliser chip activating which means that your car won't start. Contact an Peugeot specialist, or a locksmith, if this is the case.
Another common issue is when the battery in the key fob begins to fail, which causes the blade of the key to stop from entering the lock. A locksmith for cars will replace the battery and then cut a fresh blade for you. This is a quick fix.
Faulty Receiver Module
It could be that the receiver module is defective If your Peugeot key fob fails to function after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which controls the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals that block water from reaching the electronic chip inside. However prolonged exposure to water could cause damage to these seals and the chip. The high salt content of the ocean water or pool can cause damage to the key fob when it is submerged.
If your Peugeot spare key fob doesn't work You'll need the module replaced. This can only be done by an expert auto locksmith or Peugeot specialist. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the correct codes to start the car. This is the reason why you should only be able to trust a professional Peugeot locksmith with the task of creating and programming an appropriate replacement.
Faulty on-Board computer
The on-board computer of your Peugeot is responsible many functions in your car including airbags and power windows. The on-board computer displays an error code when something goes wrong. The code will be stored in the system until the issue is resolved. In most cases, this will require replacing the onboard computer.
The most common reason for the warning light for the airbag to come on is corroded or loose connections in the sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. It is important to have this issue addressed as quickly as you can, since the airbag malfunctioning could be risky in the event of an accident.
If your Peugeot is showing a card detected as not present error, the battery in the key fob might be dead or weak. This will stop the key fob from sending a signal that will disable the immobilizer on your vehicle. Try this by pressing the unlock button on the key fob and then trying to start your car. If this doesn't work then the battery in the key must be replaced.